Angelus Reforpost Fiber Glass – Refill Pack Size-1

Parallel shape with grooves: great retention
Metal filament: allows radiographic visualization
Longitudinal fibers: easy removal
For use with Peeso (Largo) drills: easy to adapt
High concentration of fibers: great mechanical properties
Modulus of elasticity similar to dentin´s: lower risk of root fracture
Conical tip: less tissue removal in apical third of root canal
Direct use (prefabricated): saves clinical time and decreases lab costs.

RECOMMENDATION: 
Support of restorations and prosthetic.

COMPOSITION:
Peeso drills: Stainless steel
Rubber Stops: Latex
Template for radiographic measurement: Plastic
REFORPOST GLASS FIBER: Glass fiber (80%);
pigmented resin (19%), stainless steel filament
(1%).
REFORPOST CARBON FIBER: Carbon fiber
(72%); pigmented resin (22%), stainless steel
filament (6%)

Parallel shape with grooves
Metal filament
Longitudinal fibers
For use with Peeso (Largo) drills
High concentration of fibers
Modulus of elasticity similar to dentin’s
Conical tip
Direct use (prefabricated)

Angelus Reforpost Fibre Glass (10 +5) Post Refill Size 1

A. ROOT CANAL PREPARATION
1. Select the pin using the template and the periapical x-ray of the tooth.
2. Remove some of the root canal filling with heated instruments to the predetermined depth. The use of drills can cause apical displacement of the gutta-percha. Allow at least 3 to 5 mm of filling at the root apex due to the presence of accessory canals, which must remain sealed to prevent bacterial contamination
3. Prepare the canal with the drill corresponding to the diameter of the selected post

B. PREPARATION OF REFORPOST FOR CEMENTATION
1. Position the pin to verify its adaptation. Make a mark on the pin 2 to 3 mm from the antagonist tooth – and cut it with a diamond bit at high rotation under cooling. Do not use scissors or pliers, because the maceration of the fiber changes the mechanical properties of the pin
2. Clean the post with alcohol and dry it
3. Apply a layer of silane (SILANO ANGELUS®) and let it dry for 1 minute
WARNING: It is not necessary to apply the silane on REFORPOST® CARBON FIBER
4. Apply the ANGELUS® FUSION-DURALINK® CATALYST to the post according to its instructions

C. CEMENTATION
1. Clean the canal with the air-water spray and dry it with air and absorbent paper points
2. Etch the canal with ANGELUS® 37% PHOSPHORIC ACID for 15 seconds
3. Wash again the canal and dry it with air and absorbent paper points Apply ANGELUS® FUSION-DURALINK® PRIMER in the canal and wait for 1 minute
4. Apply ANGELUS® FUSION-DURALINK® CATALYST according to the instructions. The adhesive components must not be mixed before application. They are polymerized chemically without light curing
5. Spatulate the resinous cement selected* and fill the conduit
6. Put the post in the canal, remove excess of the cement and wait for the polymerization. If the cement is dual, light cure it Zinc phosphate and glass ionomer cements (conventional and resin-modify ed) can also be used, but their mechanical properties are inferior to those of the resin cements. Auto-adhesive cements eliminate the needs for the steps of acid conditioning and adhesive application

D. CROWN BUILD-UP
1. Do another etching with ANGELUS® 37% PHOSPHORIC ACID and apply an adhesive on the remaining tooth structures and post. Build the crown core with composite resin, or with ANGELUS® REFORCORE®. REFORCORE® is a prefabricated glass fiber core, for the technique of direct cores

E. USE OF ACCESSORY POSTS IN WEAKENED ROOTS AND WIDE CANALS
1. Fill the remaining spaces of the canal with ANGELUS® REFORPIN® accessory posts. The decrease in thickness of the cement and the better retention provided by REFORPIN® reduce the risk of post/core loosening